Owner/Operator ManualManuel Du Propriétaire/UtilisateurModel926057 – Power Brush 36(Serial No. 000101 +)Power Brush 3604653900 4/13Printed in USAENGLI
EN - 101. Traction Drive Clutch Lever2. Speed Selector Lever3. Attachment Clutch Lever4. Brush Angle Lock Lever5. Recoil Starter Handle6. Engine Shut
EN - 11STANDARD CONTROLSSee Controls and Features on page 10.Traction Drive Clutch - Left Hand LeverSqueeze the Traction Drive Clutch Lever against th
EN - 12Throttle LeverThe throttle controls the engine speed. To increase or decrease engine speed, adjust to:1. Fast (normal or warm starts) to left2
EN - 133. Lift the brush head assembly off the ground and reverse the unit to move it away from the swept area.4. Stop engine and allow all moving par
EN - 145. Fill fuel tank to within 1/2 in (1.27 cm) below bottom of filler neck. See Specifications on page 29 for fuel tank capacity.IMPORTANT: DO NO
EN - 155. Pull recoil starter handle with a rapid continuous full arm stroke. Let rope rewind slowly.IMPORTANT: DO NOT let Starter Handle snap against
EN - 16Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine serv
EN - 17OPERATING POSITION(Figure 7)To connect the brush attachment to traction unit:1. Place attachment belts onto attachment pulley.NOTE: Holding dow
EN - 18CHECK CLUTCH OPERATIONBrush must stop quickly when attachment clutch lever is released.Wheels must stop quickly when traction drive clutch leve
EN - 19GENERAL LUBRICATION(Figure 8)1. Place unit into the service position (See Service Position on page 16).IMPORTANT: Wipe each fitting clean befor
EN - 2Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Assembly . . . . . . . . . . . . . . . . . . . . . . . . 8Controls & Features
EN - 20RECOIL GUARD FOAM COVER INSTALLATION(Figure 9)The recoil foam cover slides over the starter handle and attaches to the recoil guard with Velcro
EN - 21ATTACHMENT CLUTCH ADJUSTMENT(Figures 11, 12 and 13)Remove Attachment Cable Slack1. Remove the belt cover.2. Loosen jam nut on cable adjustment
EN - 22Check Attachment Idler Arm Roller Clearance(Figure 13)NOTE: It will be difficult to check the measurement inside the frame. Use a 1/2 in. (12.7
EN - 23TRACTION DRIVE CLUTCH ADJUSTMENT(Figure 15)If drive slips, adjust traction clutch to compensate for friction disc wear.To adjust traction clutc
EN - 242. To gain belt clearance, back out the stop screw from the frame until the drive plate assembly can swing past it (Figure 15).3. Pull idler aw
EN - 25BRUSH SEGMENT REPLACEMENT(Figure 18, 19, and 20)1. Shut off engine, close fuel shut-off valve, disconnect spark plug wire and allow unit to coo
EN - 263. Loosen each bearing setscrew and slide bearings inward, away from horizontal end supports.IMPORTANT: Brush gearbox splined shaft will separa
EN - 27IMPORTANT: Brush segments must be aligned properly so they do not nest together (Figure 19).7. Remove used brush segments and replace with new
EN - 28To obtain a complete parts manual, find your model and serial number. Then go to www.ariens.com.TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTIO
EN - 29SPECIFICATIONSModel Number 926057Engine Subaru EX27Engine Displacement – in3 (cc)16.2 (265)Fast Idle Speed – RPM 3800 ±100Starter 120VAC Electr
EN - 3DISCLAIMERAriens reserves the right to discontinue, make changes to, and add improvements upon its products at any time without public notice or
Sno-Chore 2013EN - 30Sno-Thro®, Sno-Tek® and Chore Performing Equipment Limited WarrantyAriens Company (Ariens) warrants to the original purchaser tha
Sno-Chore 2013EN - 31Exceptions and LimitationsThe chart below details special exceptions to this warranty:Customer ResponsibilitiesRegister the produ
Sno-Chore 2013EN - 32Exclusions – Items Not Covered by This Warranty• Parts that are not genuine Ariens, Gravely, Parker or Countax service parts are
Ariens Company655 West Ryan StreetBrillion, WI 54110920-756-4688Fax 920-756-2407www.ariens.com
EN - 4REQUIRED OPERATOR TRAININGOriginal purchaser of this unit was instructed by the seller on safe and proper operation. If unit is to be used by so
EN - 5EMISSION CONTROL SYSTEMThis equipment and/or its engine may include exhaust and evaporative emissions control system components required to meet
EN - 6Keep children and people away. Keep children out of work area and under watchful care of a responsible adult.NEVER allow children to operate or
EN - 7Adjust brush height before operating. Engage traction drive clutch before attachment clutch. If brush is set too low or if terrain is irregular
EN - 8Tools Required:•Tire Gauge• Pliers• 1/2-In. 3/8-In, 7/16-In, and 9/16-In Wrench and/or Adjustable WrenchUnpacking UnitUnfold Handlebar(Figure 3)
EN - 9Check Tire PressureCheck tire pressure and adjust to the pressure listed on tire sidewall.Check Engine Crankcase OilIMPORTANT: Engine is shipped
Kommentare zu diesen Handbüchern