Owner/Operator Manual Models 932102 - 520932103 - 624932310 - 624 Sno-Thro ® 03243800D 5/02Supersedes 03243800,A, B, CPrinted in USA ENGLISH FRANÇAI
GB - 10Rotating impeller can cause serious injury. DO NOT unclog unit while engine is running. When leaving operator’s position for any reason, ALW
GB - 11 MAINTENANCE AND SERVICE SAFETY RULES Before cleaning, removing clogs or making any inspections, repairs, etc.: disengage clutch(es), stop uni
GB - 12 Discharge Chute (932102) 1. Grease discharge chute ring if not already greased (Figure 4b).2. Remove mounting hardware from top of engine.3.
GB - 133. Ensure Z bend end of clutch cable is connected to hole in tab on right side of clutch bail. Check Auger Gearcase Oil Check oil level in au
GB - 14ThrottleThe Throttle controls the engine speed. To increase or decrease the engine speed, adjust to:1.Fast (normal or warm starts)2.Part-Thrott
GB - 155. Insert key into ignition switch and push into RUN position. DO NOT twist key after inserting it.6. Grasp starter handle and pull rope out sl
GB - 16Secure unit chassis to transport vehicle. NEVER secure from rods or linkages that could be damaged.DO NOT transport machine while engine is run
GB - 17To ensure adequate lubricant level:1. Remove filler plug (Figure 5). Lubricant must be at least up to bottom of lubricant filler hole with unit r
GB - 18ATTACHMENT DRIVE BELT REPLACEMENTRemove old attachment drive belt:1. Shut off engine, remove key, disconnect spark plug wire and allow unit to
GB - 19ATTACHMENT CLUTCH / BRAKE ADJUSTMENT1. Remove belt cover. 2. Check belt alignment (Figure 9).Engine sheave and attachment pulley must align ver
2 5/30/02MODEL CERTIFICATE OF CONFORMITY ISSUED BY THE MANUFACTURERCERTIFICAT DE CONFORMITÉ DU MODÈLE DÉLIVRÉ PAR LE FABRICANT MODELL-KONFORMITÄTSBES
GB - 20DISCHARGE CHUTEIf Chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on spring (F
GB - 21AUGER EDGE REPLACEMENTOver time the rubber edges of the auger will wear. Contact your Ariens Dealer for replacement.IMPORTANT: Replace rubber e
GB - 22To obtain a complete parts manual, find your model and serial number. Then go to www.ariens.com or call 1-800-678-5443.Engine stops.1. Out of fu
GB - 23SPECIFICATIONSModel Number 932102 932103 932310Description 520 624 624Engine - Tecumseh HSSK50-67409TOHSK60-71505DOHSK60-71504D Power Max - HP
GB - 243 Year Limited Sno-Thro WarrantyAriens Company warrants to the original purchaser that consumer products manufacturedby Ariens Company will be
GB - 25DURA-CLEAN™ AugerLimited Lifetime WarrantyAriens Company hereby warrants to the original purchaser that the rubber componentsof the DURA-CLEAN™
Ariens Company655 West Ryan StreetP.O. Box 157Brillion, WI 54110-0157920-756-2141Fax 920-756-2407www.ariens.com
3 5/30/02Stated Sound Power Levels are established following Annex V “Internal Control of Production” of directive 2000/14/EC and assessment procedur
4 ENGLISH 1. Attachment Clutch Bail2. Chute Control Lever (932102)Chute Crank(932103, 310)3. Muffler Guard4. Chute Deflector5. Discharge Chute6. Hous
51245678910111314151617932102OS2080OS1911Figure 11234567891012131617141511OS1746OS207193210393231018191718193
GB - 6 Controls and Features . . . . . . . . . . . . . . . . 4Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Assembly. . . . . .
GB - 7 DELIVERY Customer Note: If you have purchased this product without complete assembly and instruction by your retailer, it is your responsibil
GB - 8 SAFETY DECALS AND LOCATIONS ALWAYS replace missing or damaged Safety Decals. Refer to figure below for Safety Decal locations. 1. DANGER!2. DAN
GB - 9 ASSEMBLY SAFETY RULES Read, understand, and follow all safety practices in Owner/Operator Manual before assembling. Failure to follow instruct
Kommentare zu diesen Handbüchern